Exseed Dabcool W2 Second Generation Water Pipe Vaporizer Kit 1500mAh

Exseed Dabcool W2 Second Generation Kit

• Brand: Exseed
• Unit: set
• Type: Vaporizer
  
• Net Weight: 710(g)

The combined shipping cost will be calculated automatically by the system after you choose the shipping destination in the checkout step.

The Exseed Dabcool W2 Second Generation Kit is an upgrade version of Exseed Dabcool W2 Kit, designed for waxy oils such as shatter, wax, and other extracts. Bigger and stronger. It features the waterproof function of Exseed Second Generation atomizer is huge, it's the first waterproof atomizer that has passed the IPX4 test in the market, and they have passed 10000 times heat-up testing. The Exseed Second Generation atomizer is convenient and simple to change, they have a double structure to prevent coil contact with water, customers will only need to change a coil instead of changing the entire atomizer. Built-in a coil at atomizer, you can change the coil easily. Also adopted a 1500mAh high-performance lithium-ion battery to provide powerful heating function and long service life. Using newly program, Exseed Dabcool W2 Second Generation Kit shows more accurate temperature control. 7 colors available.

Features

▪New Atomizer Structtion, Longer Life, More Hight Performance

▪IPX4 Waterproof Atomizer, Cannot Be Immersed

▪Replacement Amotizer Coil, Comes With 1 Atomizer And 1 Coil

▪New Program, More Accurate Temperature Control

1* Alcohol Pad

1* Micro-USB Super Charger

1* Loading Tool

1* Glass Attachment

1* Atomizer

1* Replaceable Coil

1* Silicone Box

1* Carb Cap

2* Extra Bowl

STEP 1: Fully charge the device before first use. White lights pulse while charging, and turn off automatically when complete.（1 light: 0-25%; 2 lights: 25-50%; 3 lights: 50-75% ; 4 lights: 75-100%）

STEP 2: Fill glass with water just above the air-hole. Do not fill glass while attached to the base.

X- Do not allow water in the lower section!

STEP 3: Align the inlet hole on the front of the glass with an atomizer. Carefully place the glass into the base.

STEP 4: Hold the button for 3 seconds to turn on the device (same way to turn off the device). The white lights will flash once and the ambient lights will flash sequentially red>blue>green.

STEP 5: Single click to toggle through heat settings.

1 white light: 450℉ 2 white lights: 500℉

3 white lights: 600℉ 4 white lights: 680℉ The device will vibrate once while changing heat.

STEP 6: Use Loading Tool to place contents on the bottom surface of the bowl [not the side].

STEP 7: Place carb cap on top of the atomizer.

STEP 8: Double click to initiate heat-up [5 seconds avg. ], the device will vibrate twice and ambient lights will be red. Single-click the button to turn off the heat-up process at any time.

STEP 9: Ambient lights will turn green when ready. ( green lights will be on for 20 seconds, then heat up process automatically stop and ambient lights turn blue)

STEP 10: Use a cotton swab to clean the chamber after each use.

Allow chamber to fully cool before touching.

Be sure the device is powered off before cleaning.

After cleaning, allow all parts to thoroughly dry before using.

Do not blow into the glass when filled with water and attached to the base.

Do not overfill! glass with water.

Do not overfill the chamber.

Wait 1 minute between uses.

1. To check battery life: click the button 3 times, white lights will flash 3 times.

1 light: 0-25%; 2 lights: 25-50%;

3 lights: 50-75% ; 4 lights: 75-100%

2. When an atomizer is not placed or not connected well, ambient lights will flash sequentially red>blue>green then turn off.

3. Low voltage protection: when the input voltage is under 6.4V, ambient lights will flash red 3 times. when the input voltage is under 6.0V, ambient lights will flash red 3 times then the device will automatically turn off.

4. Short circuit protection: white lights will flash 5 times.

5. Overheating protection: ambient lights will be red for 5 seconds.

6. Device can be used while the battery pack is charging.

Attention: As the manufacturer needs the serial number to provide a replacement, we highly recommend you keep the original packing box or take picture of the code before discarding it. Thank you!